Mixer Yamaha TF3

Mixer Yamaha TF3

Outline

Fader Configuration		24 + 1 (Master)
Mixing Capacity	Input Channels	48 (40 mono + 2 stereo + 2 return)
	Aux Buses	20 (8 mono + 6 stereo)
	Stereo Buses	1
	Sub Buses	1
Input channel functions		8 DCA Groups
I/O	Inputs	24 mic/line (XLR/TRS combo) + 2 stereo line (RCA pin)
	Outputs	16 (XLR)

Ngoại tuyến

I/O

Khe mở rộng

1

Outline

On-board processors	DSP	8 Effects + 10 GEQ
USB		34×34 USB Audio Interface, 2-track recording via USB Storage Device

Thông số kỹ thuật chung

Tỷ lệ tần suất lấy mẫu	Bên trong	48 kHz
Độ trễ tín hiệu		Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz

General specifications

Fader

100 mm motorized, Resolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders

Thông số kỹ thuật chung

Tổng độ méo sóng hài		Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 , INPUT to OMNI OUT, Input Gain=Min. (Measured with a –18 dB/octave filter@80 kHz)
Đáp tuyến tần số		+0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT
Dãy động		110 dB typ., DA Converter, 107 dB typ., INPUT to OMNI OUT, Input Gain=Min.
Mức nhiễu & Ồn	Nhiễu đầu vào tương đương	–128 dBu typ., Input Gain=Max. (Measured with an A-Weight filter)
	Nhiễu đầu ra thặng dư	–85 dBu, ST master off (Measured with an A-Weight filter)
Xuyên âm		–100 dB (Measured with a –30 dB/octave filter@22 kHz), adjacent INPUT/OMNI OUT channels, Input Gain=Min.
Yêu cầu về nguồn điện		100–240 V 50/60 Hz
Tiêu thụ Điện		110 W
Kích thước	Rộng	716 mm (28.2in)
	H	225 mm (8.9in)
	Sâu	599 mm (23.6in)
Trọng lượng tịnh		17.0 kg (37.5lb)
Phụ kiện		Quick Guide, Power Cord, CUBASE AI download information

General specifications

Options

Expansion Card, Foot Switch (FC5)

Thông số kỹ thuật chung

Khác	Operating temperature range: 0–40 °C, Storage temperature range: -20–60 °C

Analog input characteristics

Input Terminals	GAIN	Load Impedance	For Use With Nominal	Input Level			Connector	balanced / Unbalanced
				Sensitivity*1	Nominal	Max. before clip
INPUT1-24	+66dB	7.5KΩ	50-600Ω‑ Mics or 600‑Ω Lines	-82dBu (61.6V)	-62dBu (0.616mV)	-42dBu (6.16mV)	Combo Jack (XLR-3-31 type *2 or TRS phone *3)	Balanced
	-6dB			-10dBu (245mV)	+10dBu (2.45V)	+30dBu (24.5V)
ST IN 1,2	—	10kΩ‑	600‑Ω Lines	-30dBV (31.6V)	-10dBV (316mV)	+10dBV (3.16V)	RCA Pin Jack	Unbalanced

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*In these specifications, 0dBu = 0.775Vrms.
*+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Analog output characteristics

Output Terminals	Source Impedance	For Use With Nominal	GAIN SW	Output Level		Connector	balanced / Unbalanced
				Nominal	Max. before clip
OMNI OUT 1-16	75‑Ω	600Ω‑ Lines	“+24dBu” position (default)	+4dBu (1.23 V)	+24dBu (12.3 V)	XLR-3-32 type *1	Balanced
PHONES *3	100‑Ω	40Ω‑ Phones	—	3mW	75mW	Stereo Phone Jack (TRS) *2	Unbalanced

*1.1: GND,2: HOT, 3: COLD
*2 Tip: LEFT, Ring: RIGHT, Sleeve: GND
*3 The position of the level control is lowered by 16dB from the maximum.
*In these specifications, 0dBu = 0.775Vrms.
*All output DA converters are 24bit, 128times oversampling.

Digital input/output specifications

Terminals	Format	Data length	Audio	Connector
USB (TO HOST)	USB	24bit	34ch input / 34ch output, PCM	USB (B type)
iPad	USB	—	Playback: MP3 or WAV file data / Record: WAV file data	USB (A type)

 

Control I/O specifications

Terminals	Format	Level	Connector
NETWORK	IEEE802.3	10BASE-T/100Base-TX	RJ-45
FOOT SW	—	—	TS Phone